| Inverter Ratings |
| Supply Voltage (VPN) | Applied between P - NU,NV,NW | 0 | - | 300 | V |
| Supply Voltage (VPN) | Applied between P - NU,NV,NW | 0 | - | 400 | V |
| Supply Voltage (VPN) (Surge) | Applied between P - NU,NV,NW | - | - | 500 | V |
| Collector-Emitter Voltage (VCES) | - | - | - | 600 | V |
| Output Phase Current (IC) | TC=25C, TJ<150C | - | - | 5 | A |
| Output Phase Current (IC) | TC=80C, TJ<150C | - | - | 3.5 | A |
| Output Peak Phase Current (IPK) | TC=25C, pulse width < 1ms | - | - | 10 | A |
| Short Circuit Withstand Time (tSC) | VPN400V, TJ=150C, VDD=15V | - | - | 5 | µs |
| Collector Dissipation (PC) | TC=25C, per chip | - | - | 23 | W |
| Operating Junction Temperature (TJ) | - | -40 | - | 150 | °C |
| Control (Protection) Ratings |
| Control Supply Voltage (VDD) | Applied between VDD-COM | - | 15.0 | 25 | V |
| High-Side Control Bias Voltage (VDB) | Applied between VB(U)-U, VB(V)-V, VB(W)-W | 13.5 | 15.0 | 18.5 | V |
| Input Voltage (VIN) | Applied between IN(UH), IN(VH), IN(WH), IN(UL), IN(VL), IN(WL) COM | - | - | VDD+0.3 | V |
| Fault Output Supply Voltage (VCF) | Applied between VCF-COM | - | - | COM+5.5 | V |
| Fault Output Current (ICF) | Sink current at VCF terminal | - | - | 1 | mA |
| Current Sensing Input Voltage (VSC) | Applied between CSC-COM | - | - | COM+5.5 | V |
| Temperature Output (VOT) | Applied between VOT-COM | - | - | COM+5.5 | V |
| Self Protection Supply Voltage Limit (VPN(PROT)) | VDD=13.5-16.5V, Inverter part TJ=150C, Non-repetitive, < 2µs | - | - | 400 | V |
| Module Case Operation Temperature (TC) | Measurement point of TC is provided in Figure 1 | -30 | - | 125 | °C |
| Storage Temperature (TSTG) | - | -40 | - | 150 | °C |
| Isolation Voltage (VISO) | 60Hz, sinusoidal, AC 1min, between all connected pins and heat sink
plate | - | 2000 | - | Vrms |
| Thermal Resistance |
| Junction to Case (Rth(j-c)Q) | Inverter IGBT (per 1/6 module) | - | - | 5.4 | K/W |
| Junction to Case (Rth(j-c)F) | Inverter FWD (per 1/6 module) | - | - | 8.0 | K/W |
| Electrical Characteristics |
| Collector-Emitter Saturation Voltage (VCE(SAT)) | VDD=VDB=15V, VIN=5V, IC=2.5A, TJ=25C | - | 1.20 | 1.60 | V |
| Collector-Emitter Saturation Voltage (VCE(SAT)) | IC=2.5A, TJ=125C | - | 1.25 | - | V |
| FWD Forward Voltage (VF) | VIN=0, IF=2.5A, TJ=25C | - | 1.45 | 1.95 | V |
| Switching Times (tON) | VPN=300V, VDD=VDB=15V, IC=3.5A, TJ=25C, VIN=0V 5V, Inductive load | - | 0.30 | 0.60 | 1.10 µs |
| Switching Times (tC(ON)) | - | - | 0.1 | 0.35 | µs |
| Switching Times (tOFF) | - | - | 1.1 | 1.6 | µs |
| Switching Times (tC(OFF)) | - | - | 0.10 | 0.30 | µs |
| Switching Times (trr) | - | - | 0.10 | - | µs |
| Collector-Emitter Leakage Current (ICES) | VCE=VCES, TJ=25C | - | - | 1 | mA |
| Collector-Emitter Leakage Current (ICES) | VCE=VCES, TJ=125C | - | - | 10 | mA |
| Quiescent VDD Supply Current (IQDD) | VDD=15V, IN(UH,VH,WH,UL,VL,WL) =0V | - | - | 2.1 | mA |
| Quiescent VDB Supply Current (IQDB) | VDB=15V, IN(UH, VH, WH)=0V | - | - | 0.3 | mA |
| Short-Circuit Trip Level (VSC(ref)) | VDD=15V | 0.455 | 0.48 | 0.505 | V |
| Under-Voltage Protection Trip Level (UVDT) | - | 10.3 | 11.4 | 12.5 | V |
| Under-Voltage Reset Level (UVDR) | - | 10.8 | 11.9 | 13.0 | V |
| Under-Voltage Protection Trip Level (UVDBT) | - | 8.5 | 9.5 | 10.5 | V |
| Under-Voltage Reset Level (UVDBR) | - | 9.5 | 10.5 | 11.5 | V |
| Temperature Output (VOT) | LVIC Temperature=90°C | 2.67 | 2.77 | 2.86 | V |
| Temperature Output (VOT) | LVIC Temperature=25°C | 0.8 | 1.05 | 1.3 | V |
| Over-Temperature Protection Trip Level (OTT) | OT Pin connected to VDD or open | 100 | 120 | 140 | °C |
| Hysteresis of Trip Reset (OTHYS) | - | - | 30 | - | °C |
| Fault Output Voltage (VCFH) | VSC=0V, VCF Circuit: 10kΩ to 5V pull-up | 4.9 | - | - | V |
| Fault Output Voltage (VCFL) | VSC=1V, VCF Circuit: 10kΩ to 5V pull-up | - | - | 0.5 | V |
| Fault Output Positive Going Threshold (VCF+) | - | - | 1.9 | 2.2 | V |
| Fault Output Negative Going Threshold (VCF-) | - | 0.8 | 1.1 | - | V |
| Fault Output Pulse Width (tFO) | Pull-up resistor only | 20 | - | - | µs |
| Fault Output Pulse Width (tFO) | Pull-up resistor with pull-down capacitor (RCF=2.2MΩ, CCF=1nF, 5V
pull-up) | - | 1 | - | ms |
| Input Current (IIN) | VIN=5V | - | 0.72 | - | mA |
| ON Threshold Voltage (Vth(on)) | Applied between IN(UH), IN(VH), IN(WH), IN(UL), IN(VL), IN(WL)-COM | 2.3 | 2.6 | - | V |
| OFF Threshold Voltage (Vth(off)) | - | 0.8 | 1.2 | - | V |
| ON/OFF Threshold Hysteresis Voltage (Vth(hys)) | - | - | 1.1 | - | V |
| Bootstrap Diode Forward Voltage (VF(BSD)) | IF=10mA, Including Voltage Drop by Limiting Resistor | 0.5 | 1.0 | 1.5 | V |
| Built-in Limiting Resistance (RBSD) | Included in Bootstrap Diode | 80 | 100 | 120 | Ω |
| Recommended Operation Conditions |
| Supply Voltage (VPN) | Applied between P-NU, NV, NW | 0 | - | 400 | V |
| Control Supply Voltage (VDD) | Applied between VDD-COM | 13.5 | 15.0 | 16.5 | V |
| High-Side Bias Voltage (VDB) | Applied between VB(U)-U, VB(V)-V, VB(W)-W | 13.5 | 15.0 | 18.5 | V |
| Control Supply Variation (dVDD/dt, dVDB/dt) | - | -1 | - | +1 | V/µs |
| Arm Shoot-Through Blocking Time (tdead) | For each input signal | 1.5 | - | - | µs |
| PWM Input Frequency (fPWM) | -40°C < TJ < 150°C | - | - | 20 | kHz |
| Minimum Input Pulse Width (PWIN(ON)) | - | 0.5 | - | - | µs |
| Minimum Input Pulse Width (PWIN(OFF)) | - | 0.5 | - | - | µs |
| COM Variation | Between COM-NU, NV, NW (including surge) | -5.0 | - | 5.0 | V |
| Mechanical Characteristics |
| Mounting Torque | Mounting Screw: M3 | 0.59 | 0.69 | 0.78 | N m |
| Weight | - | - | 9.12 | - | g |
| Flatness | Refer to Figure 6 | -50 | - | 100 | µm |
